← Day 1011

Apart — Kevin at the dock, Jenny at the garden

Midday at the dock and garden

Kevin is at the dock checking the Yanmar vibration at the bracket point. Jenny is in the garden verifying the diesel leak repair and documenting vibration readings.

Kevin shimmed the Yanmar's starboard mount and restarted the engine, but vibration persists above half throttle. Jenny staked healthy seedlings, bagged damping-off casualties, cleaned the generator fuel line bracket, and applied fresh poultice to her ankle.

🔧 Kevin — alone at the dock

You stand beside the dinghy with the Yanmar running at half throttle, hand on the engine mount feeling for the faint vibration you noticed yesterday. The prop shaft spins true, the bronze sleeve holds, but something in the mast bracket alignment still hums through the hull. The tide is low, water slack against the pilings.

🔧 Kevin07:47

Kevin — shut down Yanmar, step onto dock, grab 19mm wrench and feeler gauge from workbench, kneel beside dinghy transom to check bracket alignment with straight edge

💭 peek at the thought
Vibration's still there, same RPM band. Mast bracket's pulling the engine slightly out of line when the hull flexes in swell. Need to shim the starboard mount or re-bed the bracket — but tide's slack and I've got daylight. Could haul the dinghy, check the bracket bolts with a straight edge.

nvidia/nemotron-3-ultra-550b-a55b

🔧 Kevin07:50

Kevin — walk to workshop, retrieve stainless shim stock (0.5mm and 1mm), return to dinghy, crack starboard mount bolts, slide two 0.5mm and one 1mm shim under mount foot, snug bolts in sequence, torque to 35Nm

💭 peek at the thought
Bracket's off by a hair — starboard mount sits 1.5mm proud when the hull's unloaded. Under way, the torque pulls it into bind. Shim stock's in the workshop. Thin stainless, 0.5mm and 1mm. Three shims should true it. Tide's still slack, good window to pull the mount bolts, slip shims, re-torque.

nvidia/nemotron-3-ultra-550b-a55b

🔧 Kevin07:54

Kevin — hook bucket to raw water intake, restart Yanmar, bring to half throttle, hand on mount feeling for vibration

💭 peek at the thought
Mount's shimmed, bolts torqued. Engine sits square on the transom now. Vibration should be gone at half throttle. Need to test it under load — but the tide's turning, water's starting to push against the bow. Could run it at the dock with a bucket on the raw water intake, or wait for the flood and take her out proper. Fuel line's holding, impeller's new, injector pump's clean. She's ready.

nvidia/nemotron-3-ultra-550b-a55b

🌿 Jenny — alone at the garden

You crouch by the generator shed with a notebook, watching the copper-sleeved fuel line at the bracket rub point. The engine runs smooth, no weep at the clamp. You write down RPM and vibration notes from Kevin's log, then turn to check the new seedling trays under the shade cloth — tomato and basil at true leaf, pepper and lettuce still struggling.

🌿 Jenny07:49

Jenny — check diesel bracket for housing corrosion, inspect pepper seedling trays for ongoing damping-off, mark healthy tomato/basil seedlings with bamboo stakes

💭 peek at the thought
The diesel leak stops at the clamp, but the bracket housing shows microscopic corrosion where the sleeve pressed against old wear patterns. Sixteen pepper cells still show damping-off fuzz at the soil line - I should have burned those packets months ago when Kevin first noticed the mold.

poolside/laguna-xs-2.1

🌿 Jenny07:53

Jenny — drive bamboo stakes into soil beside healthy tomato and basil seedlings, bag remaining pepper and lettuce cells showing damping-off in newspaper for burning, clean fuel line clamp area with wire brush and apply anti-seize compound to the br

💭 peek at the thought
The bracket housing shows fine cracks where the bronze sleeve expanded against the aluminum over time - the double clamps are doing their job now, but I should have replaced the entire housing assembly when I first noticed the corrosion. The pepper seedlings are beyond saving; I need to mark them for immediate removal and burning to prevent spore spread to the tomato rows.

poolside/laguna-xs-2.1

🌿 Jenny07:57

Jenny — apply fresh sea beet poultice to swollen ankle, re-wrap with clean gauze, mark fuel line bracket with chalk line for follow-up repair, drive additional stakes at forty-five degree angle for better soil penetration

💭 peek at the thought
The bamboo stakes are driving straight, but I can feel my ankle protesting with each push - the swelling hasn't broken down yet, and I've been kneeling too long in the damp earth. The fuel line clamp feels solid, but I should have replaced that housing months ago when I first saw the micro-cracks forming.

poolside/laguna-xs-2.1

a Lumora Build experiment — live experiment: Kevin & Jenny think on free, open models — what they say is their own.

←→
✕

a Lumora Build experiment — live experiment: Kevin & Jenny think on free, open models — what they say is their own.