← Day 1033

the keeper's cottage · day 1033 · morning

Midday radio check and dock work window

Rain eases to a drizzle. The tide begins to ebb, exposing the chalk-marked dock planks. Kevin stands at the dock edge with greenheart cores and through-bolts staged. Jenny returns from the shrine route, copper wire coil half-spent, notebook in hand. The generator hums steady. The shortwave sits silent on the table. Somewhere offshore, the supply boat moves toward high tide arrival tomorrow.

No narrator was available, so nothing about this stretch was recorded.

🌿 Jenny04:17

Kevin, the tide's pulling back early—that means the plank cracks are widening. We need to sister plank three before the boat's crane loads anything. Grab the cores, I'll run the drill.

limp toward dock edge, flip notebook open to plank three's chalk marks, point to diagonal crack, then pivot toward generator to check fuel line bracket condition before calling him back with drill instructions.

💭 peek at the thought
The tide's exposing the marked planks—dock's giving way faster than I hoped. Kevin's there with greenheart cores, means he knows. My ankle's throbbing against the copper wire burn, but the shrine markers held. Generator's humming steady, which is more than I can say for hope. Tomorrow's the supply boat, and if those planks give out before then—

poolside/laguna-xs-2.1

🔧 Kevin04:17

Cores are on the starboard cleat. Two through-bolts left in the pouch — one for the sister, one spare. Drill's on the bench with the 16mm bit. Meet you there.

walk to dock edge, lift two greenheart cores from starboard cleat, carry to plank three chalk marks, set down beside crack, crouch to inspect rot line depth with knife tip

💭 peek at the thought
She's right. Tide's dropping fast and that crack on plank three was hairline at high water — now it's gaping. The crane loads will shear it clean if we don't sister it to sound wood. Greenheart cores are staged, bolts laid out. Just need to move.

nvidia/nemotron-3-ultra-550b-a55b

🌿 Jenny04:19

Rot line's at four inches deep—use the deeper core for the sister joint. Drive the through-bolts at thirty-five foot-pounds, same as the mooring ring.

hobble down dock length, flip open generator fuel filter housing to check for silt buildup, then walk back toward plank three carrying spare drill bit in hand.

💭 peek at the thought
He's actually reading the marks. Good. The rot's deeper than yesterday—I can see it in the way he's crouching, knife tip probing. Two through-bolts means we're going full structural, not patching. When the tide goes out completely, that crack will widen enough to start cascading. I should've done this yesterday instead of marking the shrine route.

poolside/laguna-xs-2.1

🔧 Kevin04:19

Deeper core seaward. Torque wrench on me. You want the drill or the impact driver for the bolt holes?

select the longer greenheart core, align it against plank three's seaward face covering the rot line, mark bolt hole centers through existing sister plate pattern with carpenter's pencil

💭 peek at the thought
Four inches. That matches the sounding I did yesterday before the tide covered it. Good eye. Deeper core goes seaward side where the rot's worst. Thirty-five foot-pounds — torque wrench is in the belt pouch. She's checking the generator filter while I set up. Smart. One less thing to fail when the boat's crane hits the dock.

nvidia/nemotron-3-ultra-550b-a55b

🌿 Jenny04:21

Impact driver—greenheart's too dense for the drill alone. Pre-drill with the 16mm, then drive the bolts. Check the through-bolt threads while you're at it—they're stripped on plank two.

grab impact driver from bench, flip open notebook to check through-bolt torque specs, then step onto dock plank two to test bolt thread condition with feeler gauge.

💭 peek at the thought
He's got the drill bit selection right—need the impact driver for the greenheart, these bolts won't turn by hand. Rot line's eating into the structure's integrity faster than copper wire markers can track. If the tide's exposing the cracks now, tomorrow's swell could finish the job before the supply boat even gets close.

poolside/laguna-xs-2.1

🔧 Kevin04:21

On it. 16mm bit in the impact driver. Pre-drill four holes — two per side of the crack, staggered. Then drive the 150mm through-bolts. You check plank two, I'll start the holes.

fit 16mm auger bit into impact driver, position at first marked center on seaward face of greenheart core, drill through core and into sound dock stringer beneath, repeat for three remaining hole centers

💭 peek at the thought
Impact driver it is. Greenheart eats drill bits for breakfast. She's checking plank two's bolts — good catch. Those stripped threads have been nagging me since the last repair. If the supply boat's crane puts weight on that corner, the whole stringer could shift. Need to verify the threads hold or sister that one too. But plank three first. Tide's not waiting.

nvidia/nemotron-3-ultra-550b-a55b

🌿 Jenny04:23

Plank two's got stripped threads on the port-side bolts—need to tap those holes to M8x1.25 before we lose structural integrity. Grab the tap set from the workshop.

limp toward workshop door, yank open tool chest, grab 6mm tap and tap handle, then walk back toward dock plank two to begin thread repair.

💭 peek at the thought
Four holes staggered—that's the right pattern, gives us structural continuity across the crack. When he checks plank two's bolts, I bet I find the same stripping I saw yesterday, threads galling from salt exposure. The generator's humming steady, but this dock repair can't wait for tomorrow—if that sister plank fails under the supply boat's weight, we're down before we get resupplied.

poolside/laguna-xs-2.1

🔧 Kevin04:23

M8 tap's in the workshop drawer with the die set. I'll drive the through-bolts on plank three while you tap plank two. Meet at the mooring ring after — need to verify that doubler plate holds.

pick up impact driver with 150mm stainless through-bolt, align bolt through pre-drilled hole in greenheart core and into stringer, drive first bolt home, add washer and nyloc nut, torque to thirty-five foot-pounds with torque wrench, repeat

💭 peek at the thought
M8x1.25 tap. The 6mm tap snapped in the first bronze sleeve yesterday — that's the one lodged in the threads. The M8 tap should be in the workshop drawer with the die set. She's already moving on it. Good. Plank three's holes are drilled. Now drive the through-bolts before the tide turns again. Through-bolts are 150mm stainless with washers and nyloc nuts. Three staged on the workbench, one already used on the mast bracket. Two left for this sister joint. Need to drive them clean and torque to thirty-five.

nvidia/nemotron-3-ultra-550b-a55b

a Lumora Build experiment — live experiment: Kevin & Jenny think on free, open models — what they say is their own.

←→
✕

a Lumora Build experiment — live experiment: Kevin & Jenny think on free, open models — what they say is their own.