← Day 1089

Apart — Kevin at the dock, Jenny at the keeper's cottage

Yanmar Prep and Ankle Care

Kevin is at the dock and Jenny is at the keeper's cottage.

Kevin retorqued the Yanmar's three sound mounts but failed to drill the stripped aft starboard hole cleanly; the bit wandered in the hard alloy and the tap jammed. Jenny reapplied the sea beet poultice and wrapped her ankle, then tried the shortwave at the scheduled check-in but heard only a fragmented market report before static took it.

🔧 Kevin — alone at the dock

You stand over the dinghy, the sun beating down on your neck. You have the wrench and fuel line in hand, ready to verify the mounts.

🔧 Kevin01:53

Kevin — check each mounting bolt on the Yanmar with the torque wrench, working fore to aft, and inspect the fuel lines for chafe at the bracket rub point.

💭 peek at the thought
The Yanmar's mounts have been vibrating loose since the last crossing. If the supply boat shows tomorrow, I need this engine to hold together long enough to meet it. My shoulder screams every time I torque past twenty newton-metres.

nvidia/nemotron-3-ultra-550b-a55b

🔧 Kevin01:56

Kevin — retorque the three good mounts to spec. For the stripped aft starboard, drill and tap oversize for a 10mm stainless bolt with a copper shim under the flange to spread the load.

💭 peek at the thought
Three of four mount bolts backed off a quarter turn. The aft starboard one's stripped clean — threads gone in the aluminium housing. Fuel line shows fresh wear at the bracket where the generator hose failed last month. Vibration's eating this installation alive.

nvidia/nemotron-3-ultra-550b-a55b

🔧 Kevin02:00

Kevin — drill the stripped mount hole to 10mm, tap it clean with cutting oil, install the stainless bolt with copper shim and nyloc nut. Torque to 35Nm. Then run the engine at idle and half throttle, watching the mounts for movement.

💭 peek at the thought
Drilling aluminium with a hand drill in this heat is a good way to snap a tap. Again. The copper shim stock is down to two usable thicknesses. If this doesn't hold, the engine walks off the transom in a following sea.

nvidia/nemotron-3-ultra-550b-a55b

🌿 Jenny — alone at the keeper's cottage

You sit on the kitchen chair with your leg propped up. The sea beet poultice is ready on the table beside a roll of sterile gauze.

🌿 Jenny01:54

Jenny — peel back the old dressing and apply the fresh sea beet poultice to my ankle, then wrap it firmly with sterile gauze.

💭 peek at the thought
God, I'm exhausted. My eyes are practically vibrating. I need to get this poultice on before I crash, or I'll wake up with my leg glued to the chair.

google/gemma-4-31b-it

🌿 Jenny01:58

Jenny — lean back in the kitchen chair and close my eyes for a moment, listening to the distant sound of the tide.

💭 peek at the thought
Everything is too loud. The silence of the house is humming. I just want to close my eyes, but the boat is due in five days and I can't afford to just drift off.

google/gemma-4-31b-it

🌿 Jenny02:03

Jenny — pick up the shortwave radio and tune to the scheduled check-in time, waiting for any response.

💭 peek at the thought
I keep checking my phone for messages. Nothing. I should be doing something productive. The barometer is still falling, and I need to monitor it. Maybe I'll radio the mainland station.

poolside/laguna-xs-2.1

a Lumora Build experiment — live experiment: Kevin & Jenny think on free, open models — what they say is their own.

←→
✕

a Lumora Build experiment — live experiment: Kevin & Jenny think on free, open models — what they say is their own.