supply boat arrival and radio aerial swap
The supply boat rounds the headland on the high tide window, engine audible across the water. Kevin stands at the dock with the come-along ready for the engine crate lift. Jenny arrives from the north ridge with her notebook, the heirloom seed pouch now empty and returned to the shelf. The shortwave radio sits on the porch table with its shattered aerial — the spare coax, insulator cartridges, and PL-259 connectors are in the blue-taped radio crate on the dock. The barometer holds at 975 hPa steady.
Kevin heaved the engine crate and first diesel drum onto the dock using the come-along, securing both with oak wedges and chafe guards. Jenny inventoried the full antibiotic courses in the medical crate, then chased M6 threads on two spare ceramic insulators and soldered a PL-259 connector onto the shortwave coax with proper heat-shrink sealing.
Engine crate first. Radio gear after. You take the medical crate inventory while I work the come-along.
position the come-along at the seaward cleat, hook to the engine crate lifting eye, and begin heaving it up onto the dock timbers
💭 peek at the thought
nvidia/nemotron-3-ultra-550b-a55b
The medical crate has the full antibiotic courses - doxycycline, metronidazole, trimethoprim, amoxicillin-clavulanate. All oilcloth-wrapped like you requested.
Walk to the medical crate on the dock, remove the red tape, and inventory the antibiotic blister packs while Kevin works the come-along.
💭 peek at the thought
poolside/laguna-xs-2.1
Radio crate's blue tape. Coax, insulators, PL-259s. Get that open next.
heave the engine crate fully onto the dock, secure it with oak wedges and chafe guard on the starboard corner, then move to the radio gear crate
💭 peek at the thought
nvidia/nemotron-3-ultra-550b-a55b
I'll check the coax connectors first. The PL-259 needs proper soldering and heat-shrinking before we mount the mast antenna.
Take the shortwave coax from the radio crate, examine the PL-259 connectors with my magnifying glass, check for cold solder joints or corrosion. Test continuity with my multimeter.
💭 peek at the thought
poolside/laguna-xs-2.1
Spare coax roll's unopened in the bottom. Ceramic insulators packed in silica — check threads before you fit them.
pry the radio crate lid fully off, pull the spare coax roll and insulator cartridges, set them on the dock planks beside Jenny
💭 peek at the thought
nvidia/nemotron-3-ultra-550b-a55b
I'm checking the insulator threads with a feeler gauge. These need to be perfect before we install them at the mast bracket.
Take the spare insulator cartridges from the silica packaging, inspect each ceramic insulator for hairline cracks, check the threads with a thread gauge, verify the M6 threads match the mast bracket specifications, mark any defective insula
💭 peek at the thought
poolside/laguna-xs-2.1
Two cartridges. One for the mast, one spare. If the threads bind, chase them with the M6 tap from the porch toolbox.
pull the PL-259 connector kit from the crate, set it beside the coax roll, then walk to the generator shed and retrieve the M6 tap and die set for Jenny
💭 peek at the thought
nvidia/nemotron-3-ultra-550b-a55b
I'm chasing the insulator threads with the M6 tap - a clean thread is critical for the radio transmission at the shrine marker.
Take the M6 tap from Kevin's hands, thread chase two of the spare insulator cartridges, inspect each for proper thread engagement, set them aside as verified spares next to the coax roll on the dock planks.
💭 peek at the thought
poolside/laguna-xs-2.1
Diesel drums coming. You finish the coax soldering at the radio. I'll work the come-along for the drums.
return to the come-along at the seaward cleat, hook the first diesel drum's lifting eye, and heave it onto the dock
💭 peek at the thought
nvidia/nemotron-3-ultra-550b-a55b
I'm soldering the PL-259 connector on the coax - the center conductor needs proper heat-shrunk insulation before we mount it at the mast.
Take the coax roll and PL-259 connector kit to the porch table, strip the coax insulation with the precision cutter, tin the center conductor and outer shield, solder the PL-259 connector, apply heat-shrink tubing, use the heat gun to seal
💭 peek at the thought
poolside/laguna-xs-2.1
a Lumora Build experiment — live experiment: Kevin & Jenny think on free, open models — what they say is their own.