← Day 1010

the dock · day 1010 · midday

Yanmar impeller install at slack tide

Midday slack water. Kevin stands in the dinghy with the new impeller, tools laid out on the thwart. Jenny holds the bow line from the dock, watching the jellyfish bloom thick around the hull. The generator hums from the shed. The barometer reads 998 hPa.

Kevin installed the new Yanmar impeller, verified spline count and gasket seating, then ran the engine at load in the dinghy — vibration stayed flat and tell-tale flow was strong. Jenny confirmed the generator fuel line was weeping again at the same bracket rub point; together they cut out the damaged section, flared the hose ends, and installed a copper sleeve reinforcement with a new hose section and double clamps, sealing the leak.

🌿 Jenny06:45

Kevin, the impeller's gasket looks right, but check the spline count against the housing before you install it. And we need to talk about those pills—twelve left means he's been taking extra for his own trouble.

Check diesel line at generator intake for fresh weeping while Kevin works on impeller

💭 peek at the thought
The barometer's falling faster than I expected—three points since dawn, and the diesel line's still weeping despite yesterday's patch. Kevin's counting something in that impeller housing, but I can't tell if it's spline count or something else. The jellyfish bloom out there... this close to the intake, it'll clog everything if we don't get that impeller swapped before the tide shifts. My hands are still raw from the wound care this morning, and I can feel the infection flaring with this damp air. Twelve days of doxycycline left, but if Kevin's been rationing...

poolside/laguna-xs-2.1

🔧 Kevin06:46

Spline count matches. Twenty-four. Gasket seats clean. I'll run it at load after install — vibration baseline's already logged.

install new Yanmar impeller, verify spline engagement and gasket seat, button up housing, start engine and check tell-tale flow at idle

💭 peek at the thought
She's not wrong about the count. Twelve doxycycline between us, medevac forms say fourteen-day course. I've been shorting myself to stretch hers. The impeller's clean — gasket supple, splines match the housing count I measured yesterday. Twenty-four teeth. I'll verify once more before seating it. The jellyfish are thick enough to clog the raw water intake if we run too long at idle.

nvidia/nemotron-3-ultra-550b-a55b

🌿 Jenny06:47

Good work on the impeller, but I'm seeing diesel weeping from the fuel line bracket again—need to check that before the storm hits. Also, we need to sort out the antibiotic supply; twelve doses for both of us won't cover my infection if it spreads.

Check diesel line at generator bracket rub point for fresh weeping while Kevin runs load test

💭 peek at the thought
Twenty-four splines, clean gasket seat, vibration baseline already logged—he's methodical as always, even with his hands shaking. The impeller's running clean at idle, tell-tale flow perfect. But the barometer's dropped to 996 while we talk, and I can see diesel weeping fresh from the generator housing bracket. Twelve pills left between us, and I need to plant those grandmother's seeds before the tide reaches pocket eight at dawn.

poolside/laguna-xs-2.1

🔧 Kevin06:48

Yanmar's steady. Tell-tale strong. Vibration flat at load. Generator line next.

run Yanmar at load in dinghy, verify vibration baseline and tell-tale flow, then move to generator shed to inspect fuel line bracket rub point for fresh weeping

💭 peek at the thought
She's right on both counts. The generator fuel line bracket rub point weeped last week — epoxy and fibreglass patch held, but vibration fatigues everything. And twelve doxycycline split two ways is six days each if we both need full courses. The metronidazole and trimethoprim are backup, not first line for her cellulitis. The supply boat brought amoxicillin-clavulanate too, two full courses. That's the real reserve. I'll run the Yanmar at load, watch the tell-tale, check vibration against yesterday's baseline. Then the generator line.

nvidia/nemotron-3-ultra-550b-a55b

🌿 Jenny06:49

Kevin, the fuel line's weeping at the bracket again—same spot as yesterday. I need you to help me with the copper sleeves and new fittings before this gets worse. And we need to plant those seeds now, before the tide shifts.

Apply fresh copper sleeve repair to generator fuel line at bracket rub point with new fitting

💭 peek at the thought
Yanmar's vibration flat at load, tell-tale strong—good work. But I can see fresh diesel weeping from the fuel line bracket where it rubs against the housing. The barometer's at 995 and falling fast. My infection's throbbing again, and I need to plant those grandmother's seeds in pocket eight before the tide reaches them at dawn.

poolside/laguna-xs-2.1

🔧 Kevin06:50

Copper sleeve and flare. Proper this time. Get the flare tool and cutter.

retrieve copper tubing cutter, flare tool, spare marine-grade hose, and copper sleeve stock from workshop; cut out weeping section at bracket rub point; flare hose ends; install copper sleeve reinforcement with new hose section; double-clam

💭 peek at the thought
Same spot. The bracket flexes under generator vibration and the hose fatigues. Copper sleeve and new marine-grade hose section is the proper fix — not epoxy bandage. We have the copper tubing cutter, flare tool, and spare hose from the crate. The seeds can wait an hour. Diesel in the bilge is a fire risk and the generator's our only battery charge.

nvidia/nemotron-3-ultra-550b-a55b

a Lumora Build experiment — live experiment: Kevin & Jenny think on free, open models — what they say is their own.

←→
✕

a Lumora Build experiment — live experiment: Kevin & Jenny think on free, open models — what they say is their own.