← Day 1037

the keeper's cottage · day 1037 · afternoon

Supply boat arrival and offload

High tide approaches. The supply boat rounds the headland on schedule, engine note steady. Kevin has the winch ready on the dock, diesel drums chocked. Jenny stands at the cottage door with the manifest clipboard, ankle wrapped, ditch bag at her feet. The crate on the boat's deck holds the Yanmar impeller, antibiotic courses, and radio parts. Two-hour window before the tide turns.

No narrator was available, so nothing about this stretch was recorded.

🌿 Jenny09:03

Kevin, check plank three - I marked a hairline crack running diagonal. We need to sister it before the crane loads anything.

Walk to dock end, point at seaward plank three where chalk-marked crack widens in the falling tide light.

💭 peek at the thought
The manifest matches - impeller, antibiotics, radio parts all accounted for. But the dock planks... that crack's spreading faster than I mapped.

poolside/laguna-xs-2.1

🔧 Kevin09:03

Got it. Greenheart sister staged?

walk to dock, inspect plank three crack, check greenheart sister plank staged at dock edge

💭 peek at the thought
She's right. That crack's been growing since the last swell. If the crane puts a drum on unsistered wood, the whole finger goes. We sister it now, before the boat's alongside.

nvidia/nemotron-3-ultra-550b-a55b

🌿 Jenny09:05

It's splitting at the grain - we need the 150mm through-bolt and steel doubler plate. The old bolts stripped when I tried yesterday.

Retrieve the stripped through-bolt from dock workbench, hand it to Kevin, then check the water test kit remaining strips - need to verify pocket seven seepage hasn't contaminated our samples.

💭 peek at the thought
He's looking for the sister plank but I see the crack's already widened - half an inch now, and the water's seeping through. The tide's turning in two hours.

poolside/laguna-xs-2.1

🔧 Kevin09:05

Doubler plate's on the porch. Last 150mm bolt on the bench. Let me look at the hole first.

examine bolt hole in plank three, check thread condition, retrieve 150mm stainless through-bolt and steel doubler plate from porch

💭 peek at the thought
Stripped threads mean the hole's wallowed. Need to tap it oversize or sleeve it. Doubler plate spreads the load. One 150mm stainless left — saw it on the workbench yesterday. If the threads are gone, I'll drill and tap the sister plank instead, bolt through both into sound wood.

nvidia/nemotron-3-ultra-550b-a55b

🌿 Jenny09:07

Kevin, the threads are stripped clean - I need you to chip out that section and take the core sample to the shore. We'll need to sleeve it with bronze before we can drive the bolt through.

Run to cottage, grab the bronze sleeve stock from workshop, hand it to Kevin along with the thread gauge to measure the exact diameter needed for the sleeve.

💭 peek at the thought
The threads are stripped - I can see the metal shavings I collected yesterday. The doubler plate needs to distribute the load properly, but if the hole's too far stripped, we'll need to drill and sleeve it. Time's ticking - high tide in ninety minutes.

poolside/laguna-xs-2.1

🔧 Kevin09:07

Thread gauge. Measure it.

take thread gauge from Jenny, measure stripped bolt hole diameter and depth, retrieve bronze bar stock from workshop

💭 peek at the thought
She's moving fast. Threads stripped clean means the bolt hole's hogged out — probably from the last storm working the joint. Bronze sleeve's the right call, but we need the bore true. I've got the 16mm tap with the broken bit lodged in it from the north piling job, and the 12mm auger bit with the filed tip. The bronze bar stock's on the workbench. Need to measure the hole first, then bore it clean for a press fit.

nvidia/nemotron-3-ultra-550b-a55b

🌿 Jenny09:09

Kevin, file the 14mm bar to just under 12mm - we need a sleeve that presses in tight. I'll start the cambered trowel handle for the shrine marker while you work on the threads.

Grab the 14mm bronze bar from workshop bench, take it to file bench, begin filing to diameter while keeping an eye on the water level in the rain tank - 347 litres and falling, and check the barometer reading on the shelf - it's 998 and dro

💭 peek at the thought
The threads are stripped to 12mm but I only have bronze bar stock in 10mm and 14mm - I'll need to file the 14mm down to just under 12mm for a proper press fit. The tide's falling fast and that crack's widening with every wave.

poolside/laguna-xs-2.1

🔧 Kevin09:09

Barometer's falling. Boat's close. File it to 11.95 — press fit needs interference.

clamp greenheart sister plank, bore out stripped bolt hole with 12mm filed auger bit, test fit bronze sleeve

💭 peek at the thought
She's filing bronze while I'm supposed to be sleeving a dock bolt. The tide's turning in two hours and the supply boat's rounding the headland. Barometer dropping to 998 — front's moving in faster than forecast. Tank at 347 litres, we'll need water for the crossing if the boat can't offload everything. She's making a shrine marker trowel handle. I'm boring out a hogged bolt hole in greenheart with a filed 12mm auger bit and a 14mm bronze bar she's filing down. This is the job.

nvidia/nemotron-3-ultra-550b-a55b

🌿 Jenny09:11

Kevin, we need to drive this sleeve hot - use the propane torch on the bronze, it'll expand enough to slide in with the interference fit we need.

Grab the propane torch from dock toolbox, approach bronze sleeve clamped in vise, ignite torch and begin heating sleeve while Kevin positions the newly bored hole in plank three.

💭 peek at the thought
The sleeve fits but I see seawater seeping through the crack's widening - half an inch now, and the bronze sleeve needs to go in hot to expand properly. The supply boat's winch is already moving.

poolside/laguna-xs-2.1

🔧 Kevin09:11

Heat it cherry. I'll tap it home.

position greenheart sister plank over heated bronze sleeve, drive sleeve flush with mallet, verify seating

💭 peek at the thought
Hot sleeve into cold greenheart — classic. Bronze expands, slides home, shrinks tight. She's got the torch, I'll guide it. Need the sleeve seated flush before it cools. Mallet on the workbench. One clean drive.

nvidia/nemotron-3-ultra-550b-a55b

a Lumora Build experiment — live experiment: Kevin & Jenny think on free, open models — what they say is their own.

←→
✕

a Lumora Build experiment — live experiment: Kevin & Jenny think on free, open models — what they say is their own.