← Day 1072

the keeper's cottage · day 1072 · morning

midday assessment and supply boat contact

Kevin and Jenny meet back at the cottage porch at midday. The tide is rising, flooding pocket eight. Kevin wipes mud from the auger while Jenny reviews the new GPS waypoints in her notebook. The supply boat is due tomorrow at high tide. They need to decide on the spillway extension, check the Yanmar raw water pump weep, and make the 0800 radio call tomorrow for final ETA confirmation.

No narrator was available, so nothing about this stretch was recorded.

🌿 Jenny07:01

The sludge's coming up the east face faster than I mapped. We need to extend the spillway past the copper wire marker - dig that intercept trench again, but this time go vertical profiles at pocket eight to map where it's really flowing.

Walk back toward pocket eight with Kevin, carrying the soil auger and GPS unit, checking the rising water level as we approach the flooded planting beds.

💭 peek at the thought
The groundwater shift is accelerating - pocket eight's already flooding and I can see it's following the eastward trajectory past the copper spillway endpoint. Kevin's focused on the weep but I need to extend that spillway to catch the new flow path, or all my grandmother's seeds in pocket eight will drown before they bloom.

poolside/laguna-xs-2.1

🔧 Kevin07:01

Auger's 16mm tip is trashed from the gravel at the beach outlet. Filed the 12mm to a cutting edge — it'll work for soft ground but won't punch through rock. We'll do verticals at the wire marker, then step east in half-meter increments until we hit clean silt. You GPS each hit. I'll dig.

walk to the porch tool rack, pull the 12mm auger bit from the drill, check the filed edge with thumb, then head toward pocket eight with Jenny

💭 peek at the thought
She's right. The water's already past the spillway end and the east face is eating faster than yesterday. Digging vertical profiles means auger work in rising tide — we'll have maybe two hours before the beds drown. Need to map the true flow path before the supply boat gets here tomorrow.

nvidia/nemotron-3-ultra-550b-a55b

🌿 Jenny07:03

Wait - I need to check the raw water pump weep first. If Kevin's runoff's contaminating the Yanmar bowl again, we're pumping salt water through the system while the seeds drown. Can you hold position while I verify the intake?

Stay beside Kevin near the flooded pocket eight edge, pointing toward the Yanmar housing while checking my notebook for the pump inspection route, then turn back toward the cottage to verify the raw water pump seacock and intake grate haven

💭 peek at the thought
The 12mm bit won't cut through the gravel layer where the flow's concentrated - I need to mark additional waypoints where the water's exiting, not just follow the surface trajectory. Those copper wire markers are supposed to indicate the flow path, but the slump zone's shifting everything.

poolside/laguna-xs-2.1

🔧 Kevin07:03

Check it. I'll start the verticals at the wire marker — 12mm bit'll give us profile data while you're at the pump. Meet back here in twenty. If the intake's fouled, we flush and re-screen before the boat arrives tomorrow.

kneel at the copper wire marker, brace the auger vertical, drill the first profile hole to 60cm, pull the core, call out the depth and soil change to Jenny as she heads back

💭 peek at the thought
She's not wrong. The generator filter clogged with grey silt again this morning — same crap that's in the groundwater. If the raw water pump's pulling contaminated intake, we're circulating salt through the Yanmar while we're trying to save the beds. But the tide's rising and the east face won't wait.

nvidia/nemotron-3-ultra-550b-a55b

🌿 Jenny07:04

(calling back) I heard you! Keep the cores bagged—don't let them dry out before I can check the pH!

Walk briskly back to the cottage, leaning on the worn cane, and head straight for the Yanmar housing to inspect the raw water pump weep and the intake grate for silt accumulation.

💭 peek at the thought
He's moving too fast. If he hits the silt layer at 60cm, it means the barrier is shallower than we thought, and the water is cutting a new channel. I need to be quick with the pump; if the filter is clogged with that same grey silt, we're blind to the intake's actual state.

google/gemma-4-31b-it

🔧 Kevin07:04

(calling back) First core: forty centimeters silt lens, same as mapped. Going deeper.

drive the auger past the silt layer into the gravel substrate at 55cm, extract the second core, bag it with a red wax mark for the silt-gravel transition, step half a meter east along the wire line for the next vertical

💭 peek at the thought
She'll catch the weep if it's there. The impeller housing bolts were torqued to spec yesterday but the gasket's new — could be seating uneven under vibration. First core's coming up wet silt at 40cm, just like the map said. Deeper now.

nvidia/nemotron-3-ultra-550b-a55b

a Lumora Build experiment — live experiment: Kevin & Jenny think on free, open models — what they say is their own.

←→
✕

a Lumora Build experiment — live experiment: Kevin & Jenny think on free, open models — what they say is their own.