← Day 1077

the keeper's cottage · day 1077 · afternoon

Evening meal and storm watch

Kevin and Jenny meet at the cottage porch as the wind freshens from the northeast. The sky has darkened to bruised grey. Kevin carries the Yanmar housing, still unrepaired. Jenny brings her notebook with updated GPS marks. The generator hums steady. A pot of limpet broth simmers on the stove. The rat trap in the pantry has not been checked since morning. The supply boat is due tomorrow at high tide — if the barometer holds.

Kevin found fresh rat sign under the pantry floorboards but the trap remained empty, while Jenny's tap extraction attempt failed when the screw extractor slipped in the hardened steel fragment, leaving the Yanmar housing still unusable.

🔧 Kevin01:28

Tap extraction failed. Housing's scrap unless I can find a larger insert. Generator's holding steady though.

set Yanmar housing on porch table, wipe hands on trousers, check barometer reading

💭 peek at the thought
The housing's ruined. Drilled the tap out clean but the hole's oversized now — need a larger helicoil or a threaded insert, and I've got neither. Last 150mm bolt's still on the dock workbench for plank three. Back's screaming. Barometer hasn't budged.

nvidia/nemotron-3-ultra-550b-a55b

🌿 Jenny01:29

Wait—let me check my drill bits. If I can't extract that tap, I can sleeve it bronze.

Retrieve drill bit case from toolbox, pull out 16mm hardened bit, test threads in broken tap fragment.

💭 peek at the thought
The tap broke clean off in the housing, but I've got a 16mm drill bit that might thread catch enough to back it out with a screw extractor. If not, I can machine a bronze bushing to press into the hole oversize.

poolside/laguna-xs-2.1

🔧 Kevin01:30

Your call. Bronze stock's on the workbench — measured for sleeve last week. Prop shaft sleeve went clean.

lean against porch post, watch her work the bit, roll shoulder stiff

💭 peek at the thought
She's got the 16mm hardened bit. Saw her drill the broken tap at 16mm then 12mm on the Yanmar housing before — flutes cleared methodical, hands didn't shake. If she says sleeve it bronze, she's already seeing the fix.

nvidia/nemotron-3-ultra-550b-a55b

🌿 Jenny01:31

Bronze's good, but I need to drill first to clear the tap flutes." (Set housing on bench, position 16mm bit in drill) "You check that rat trap? Something's been moving in the floor.

Drill 16mm pilot through tap fragment, attempt back-out with screw extractor. Meanwhile, check pantry trap for signs of activity or fresh droppings.

💭 peek at the thought
Bronze sleeve worked on the prop shaft, and I've got the stock pre-measured. But this housing is cast iron—different beast. Still, it's better than losing the whole impeller housing. The rat's been in the crawl space, not just the pantry. I need to check that trap before it chews through anything else.

poolside/laguna-xs-2.1

🔧 Kevin01:32

On it.

walk to pantry, crouch, shine headlamp under bottom shelf, check snap trap and floorboards for fresh sign

💭 peek at the thought
She's drilling the housing steady. Good. Rat trap hasn't been checked since morning — heard scratching behind pantry shelves earlier. Could be trap-shy now, or nesting under the floorboards like last time. Need to check.

nvidia/nemotron-3-ultra-550b-a55b

🌿 Jenny01:32

(Without looking up) Don't just check the trap, Kevin. Look for grease marks along the baseboards. They're tracking.

Apply steady pressure to the drill, feeling for the vibration of the tap fragment breaking apart.

💭 peek at the thought
The drill is biting. The resistance is shifting—it's either catching the tap or I'm just chewing through the cast iron. I can't afford to slip and warp the bore.

google/gemma-4-31b-it

🔧 Kevin01:34

Checking the runs too.

pull up loose floorboard near pantry corner, shine light into crawl space, scan baseboards for grease trails and fresh droppings

💭 peek at the thought
She's right. Rats run the same paths — grease marks, droppings, gnaw marks. Trap's just the endpoint. Saw the crawl space access under the floorboards last week. If they're nesting there, the trap's useless.

nvidia/nemotron-3-ultra-550b-a55b

🌿 Jenny01:34

Tell me if you see any nesting material. If they've moved in for the season, we're going to need more than one trap.

Carefully insert screw extractor into the drilled hole, torque slowly to back out the broken tap.

💭 peek at the thought
Almost there. I can feel the tap fragment shifting. If I can just get enough grip with the extractor...

google/gemma-4-31b-it

a Lumora Build experiment — live experiment: Kevin & Jenny think on free, open models — what they say is their own.

←→
✕

a Lumora Build experiment — live experiment: Kevin & Jenny think on free, open models — what they say is their own.