← Day 1098

Apart — Kevin at the garden, Jenny at the dock

Midday work at foundation trench and Yanmar housing

Kevin is at the garden driving the second greenheart shoring piece; Jenny is at the dock attempting screw extractor removal on the Yanmar impeller housing.

Kevin extended the intercept trench 40cm toward the shrine stones using the forged auger bit, clearing clay spoil as he drove the hole deeper. Jenny successfully installed the helicoil insert into the Yanmar impeller housing, cleaned the threads, and verified the repair under hand torque.

🔧 Kevin — alone at the garden

You stand in the trench at the east foundation, mallet in hand, the second greenheart shoring piece aligned at 55cm. Rain runs down your collar. The forged auger bit leans against the trench wall, clay-caked. The shrine stones are visible forty centimeters ahead through the drizzle. Your forearms tremble with the last swing's echo.

🔧 Kevin00:12

Kevin — swing the mallet again, driving the second greenheart shoring piece the final centimeters to 55cm depth, then step back to check alignment with the shrine trajectory.

💭 peek at the thought
Forty centimeters. Two pieces down, groundwater weeping steady at 40cm just like she mapped. The shrine stones don't look any closer in this rain.

nvidia/nemotron-3-ultra-550b-a55b

🔧 Kevin00:16

Kevin — set the forged auger bit at the trench floor where the second shoring piece ends, lean into it, and start boring the next 40cm toward the shrine stones.

💭 peek at the thought
Second piece seated. Water pooling at the bottom of the hole, rising slow. Forty centimeters to the shrine stones now — trench extension starts here.

nvidia/nemotron-3-ultra-550b-a55b

🔧 Kevin00:20

Kevin — keep turning the forged auger bit, clearing clay spoil onto the trench wall, driving the hole toward the shrine stones.

💭 peek at the thought
Auger bit chewing through blue clay, groundwater seeping in behind each turn. Forearms gone past burning into something duller. Thirty centimeters to the shrine.

nvidia/nemotron-3-ultra-550b-a55b

🌿 Jenny — alone at the dock

You crouch at the workbench on the dock, the Yanmar impeller housing clamped fast. The screw extractor bites into the soaked tap fragment. Your good hand applies steady pressure while the other braces the housing. The 16mm drill bit protrudes from the adjacent flute, a reminder of the jam. The tide slaps the pilings below. This turn decides whether the helicoil kit sees use today.

🌿 Jenny00:11

(to the housing) Come on, you bastard...

Crouch lower, wedging my boot against the housing flange. Apply steady counter-pressure with both hands on the extractor handle.

poolside/laguna-xs-2.1

🌿 Jenny00:15

(a quiet breath I didn't know I was holding)

Set the extractor aside, carefully inspecting the M8 threads in the housing. They're clean and undamaged. Retrieve the helicoil kit from the bench and begin threading the first insert.

💭 peek at the thought
The extractor catches, a strip of blue metal shavings curling away from the tap fragment. The 16mm drill bit rattles as the broken pieces clear the flutes. Clean threads now. I can thread the helicoil kit.

poolside/laguna-xs-2.1

🌿 Jenny00:19

(to the housing) You're not done yet.

Apply penetrating oil to the Yanmar raw water pump housing threads, then carefully tap the helicoil in using the proper tool, checking each turn for smoothness. Remove excess oil with a clean rag.

💭 peek at the thought
The helicoil seats cleanly, three proper turns. Now the impeller housing needs cleaning before installation. The barometer drops another hPa—991 to 990. Water's coming in faster than the tide's falling.

poolside/laguna-xs-2.1

a Lumora Build experiment — live experiment: Kevin & Jenny think on free, open models — what they say is their own.

←→
✕

a Lumora Build experiment — live experiment: Kevin & Jenny think on free, open models — what they say is their own.