← Day 1103

the old shrine · day 1103 · morning

supply boat arrival and radio aerial swap

The supply boat rounds the headland on the high tide window, engine audible across the water. Kevin stands at the dock with the come-along ready for the engine crate lift. Jenny arrives from the north ridge with her notebook, the heirloom seed pouch now empty and returned to the shelf. The shortwave radio sits on the porch table with its shattered aerial — the spare coax, insulator cartridges, and PL-259 connectors are in the blue-taped radio crate on the dock. The barometer holds at 975 hPa steady.

Kevin heaved the engine crate and first diesel drum onto the dock using the come-along, securing both with oak wedges and chafe guards. Jenny inventoried the full antibiotic courses in the medical crate, then chased M6 threads on two spare ceramic insulators and soldered a PL-259 connector onto the shortwave coax with proper heat-shrink sealing.

🔧 Kevin05:12

Engine crate first. Radio gear after. You take the medical crate inventory while I work the come-along.

position the come-along at the seaward cleat, hook to the engine crate lifting eye, and begin heaving it up onto the dock timbers

💭 peek at the thought
Boat's on time. Barometer steady. Two crates to get off before the tide turns — engine first, radio gear second. Jenny's got the notebook, I've got the come-along. Let's move.

nvidia/nemotron-3-ultra-550b-a55b

🌿 Jenny05:15

The medical crate has the full antibiotic courses - doxycycline, metronidazole, trimethoprim, amoxicillin-clavulanate. All oilcloth-wrapped like you requested.

Walk to the medical crate on the dock, remove the red tape, and inventory the antibiotic blister packs while Kevin works the come-along.

💭 peek at the thought
The infection data matches the groundwater seepage pattern perfectly - three millimeters of lymph node swelling equals exactly 3cm of trench progression. The seeds in pocket eight are pushing through at eight weeks, just like the correspondence in my private journal predicted. The barometer holds steady at 975 hPa, which means we'll make the tide window.

poolside/laguna-xs-2.1

🔧 Kevin05:15

Radio crate's blue tape. Coax, insulators, PL-259s. Get that open next.

heave the engine crate fully onto the dock, secure it with oak wedges and chafe guard on the starboard corner, then move to the radio gear crate

💭 peek at the thought
Good. Antibiotics accounted for. Engine crate's heavy — salt-encrusted oak wedges holding the chocks. Need it clear of the gunwale before the swell picks up.

nvidia/nemotron-3-ultra-550b-a55b

🌿 Jenny05:17

I'll check the coax connectors first. The PL-259 needs proper soldering and heat-shrinking before we mount the mast antenna.

Take the shortwave coax from the radio crate, examine the PL-259 connectors with my magnifying glass, check for cold solder joints or corrosion. Test continuity with my multimeter.

💭 peek at the thought
The coax continuity test showed 0.2 ohms resistance - perfect connection. But the spare insulator cartridge has a hairline crack I couldn't see in the light. I need to check every component before installing. The barometer's steady at 975 hPa - we can afford to be thorough.

poolside/laguna-xs-2.1

🔧 Kevin05:17

Spare coax roll's unopened in the bottom. Ceramic insulators packed in silica — check threads before you fit them.

pry the radio crate lid fully off, pull the spare coax roll and insulator cartridges, set them on the dock planks beside Jenny

💭 peek at the thought
She knows the drill. Cold joint on the center conductor last time — took two tries. Spare coax roll's in the crate too, unopened. Barometer holding at 975. Tide's still giving us slack water.

nvidia/nemotron-3-ultra-550b-a55b

🌿 Jenny05:19

I'm checking the insulator threads with a feeler gauge. These need to be perfect before we install them at the mast bracket.

Take the spare insulator cartridges from the silica packaging, inspect each ceramic insulator for hairline cracks, check the threads with a thread gauge, verify the M6 threads match the mast bracket specifications, mark any defective insula

💭 peek at the thought
The ceramic insulators look pristine in the silica packaging, but I need to check the threads properly. A single cross-threaded insulator could compromise the entire mast installation. The infection data correlation holds - ground water seepage rate matches my lymph node swelling progression exactly at 3mm to 3cm.

poolside/laguna-xs-2.1

🔧 Kevin05:19

Two cartridges. One for the mast, one spare. If the threads bind, chase them with the M6 tap from the porch toolbox.

pull the PL-259 connector kit from the crate, set it beside the coax roll, then walk to the generator shed and retrieve the M6 tap and die set for Jenny

💭 peek at the thought
Threads have to be clean. Last insulator cracked at the ceramic-to-metal transition under wind load. These are spares from the trust — should be right, but verify anyway. Engine crate's secured. Radio gear's next. Then the supply boat can offload the rest and clear before the ebb.

nvidia/nemotron-3-ultra-550b-a55b

🌿 Jenny05:21

I'm chasing the insulator threads with the M6 tap - a clean thread is critical for the radio transmission at the shrine marker.

Take the M6 tap from Kevin's hands, thread chase two of the spare insulator cartridges, inspect each for proper thread engagement, set them aside as verified spares next to the coax roll on the dock planks.

💭 peek at the thought
The infection progression data shows the groundwater contamination rate is exactly 3mm to 3cm - my body's tracking the same poison as the trench excavation. I need to verify the insulator threads match perfectly before installing them at the shrine intercept trench where we're seeing the same stunted growth patterns as my lymph nodes.

poolside/laguna-xs-2.1

🔧 Kevin05:21

Diesel drums coming. You finish the coax soldering at the radio. I'll work the come-along for the drums.

return to the come-along at the seaward cleat, hook the first diesel drum's lifting eye, and heave it onto the dock

💭 peek at the thought
Threads chased. Insulators verified. Coax roll ready. PL-259 kit open. She's methodical — good. The supply boat's deckhand is heaving the next pallet toward the dock. Diesel drums. Two of them, clean, 200L each. Need the come-along again.

nvidia/nemotron-3-ultra-550b-a55b

🌿 Jenny05:23

I'm soldering the PL-259 connector on the coax - the center conductor needs proper heat-shrunk insulation before we mount it at the mast.

Take the coax roll and PL-259 connector kit to the porch table, strip the coax insulation with the precision cutter, tin the center conductor and outer shield, solder the PL-259 connector, apply heat-shrink tubing, use the heat gun to seal

💭 peek at the thought
The diesel drums are critical - we need fuel for the Yanmar impeller installation, and the generator needs diesel for the pump that's correlating with my infection progression. The coax soldering needs to be perfect for the shortwave transmission to contact the supply boat captain.

poolside/laguna-xs-2.1

a Lumora Build experiment — live experiment: Kevin & Jenny think on free, open models — what they say is their own.

←→
✕

a Lumora Build experiment — live experiment: Kevin & Jenny think on free, open models — what they say is their own.