second diesel drum and radio crate completion
Kevin has the second diesel drum secured on the dock. Jenny has the shortwave coax soldered and tested, with the second PL-259 in progress. The engine crate, medical crate, and first diesel drum are all landed. The supply boat waits offshore, winch cable slack. Warm rain falls on and off. They meet at the radio crate to finish the coax run and plan the aerial insulator swap at the mast.
Kevin installed the ceramic insulator and copper shim on the mast bracket, then hoisted the spare coax to the bracket level. Jenny monitored SWR from the ground, reading a stable 1.8:1 as Kevin torqued the locknut, confirming the aerial repair was electrically sound.
Second PL-259 next. Then mast. Want you on the ground with the radio — talk me through SWR readings while I'm up there.
pull the spare coax roll and remaining insulator cartridges from the radio crate onto the dock planks, then walk to the mast base with the ceramic insulator and self-amalgamating tape
💭 peek at the thought
nvidia/nemotron-3-ultra-550b-a55b
I'm on the ground. You want me to hold the radio and watch the SWR meter while you work?
Walk to the cottage door, grab the multimeter from the radio shelf, then head to the dock where Kevin is setting down the coax components. Check the spare coax roll for any damage, then hand him the first insulator cartridge.
💭 peek at the thought
poolside/laguna-xs-2.1
Aye. Radio on low power, 2182. Call me every thirty seconds — if the needle jumps, I stop. Hand me the insulator and the shim stock.
take the ceramic insulator cartridge from Jenny, check the threads are clean, then walk to the mast base and uncoil the spare coax to inspect the full run for nicks or salt crust before hauling it aloft
💭 peek at the thought
nvidia/nemotron-3-ultra-550b-a55b
I'm on 2182, low power. Go ahead with the insulator—just let me know when you're ready to test.
Set the handheld VHF to 2182 kHz, low power setting, then grab the multimeter and a length of clean cloth from the workbench.
💭 peek at the thought
poolside/laguna-xs-2.1
Coax clean. Hauling up. Need the 0.5mm copper shim from the porch toolbox — toss it up if you can, or I'll come down.
tie the coax end to the mast halyard with a bowline, hoist it hand-over-hand to the bracket level, then brace against the mast and test-fit the ceramic insulator in the bracket to confirm the cant
💭 peek at the thought
nvidia/nemotron-3-ultra-550b-a55b
I've got the shim. Hold on—I'm running down to the porch.
Grab the 0.5mm copper shim from the porch toolbox and climb down the lower paling to reach the dock level, then walk toward the cottage where the shim stock is kept.
💭 peek at the thought
poolside/laguna-xs-2.1
Take your time. Bracket's canted starboard side low — three mill. Shim'll fix it.
hold position braced against the mast, test-fit the insulator cartridge threads into the bracket to confirm engagement, and watch the coax run for chafe at the spreader level as it pays out
💭 peek at the thought
nvidia/nemotron-3-ultra-550b-a55b
I'm going to the porch. Got the shim right here.
Walk back to the cottage, retrieve the copper shim from the porch toolbox, then head toward the dock where Kevin is waiting with the mast.
💭 peek at the thought
poolside/laguna-xs-2.1
Shim's good. Seating now.
slide the 0.5mm copper shim under the insulator base flange on the starboard side, thread the ceramic cartridge into the bracket by hand until seated, then torque the locknut with the 19mm wrench
💭 peek at the thought
nvidia/nemotron-3-ultra-550b-a55b
I'm reading 1.8:1 on the SWR meter. Stable.
Hold the multimeter to check the coax continuity at the base while Kevin finishes tightening the locknut, then prepare to test the full connection.
💭 peek at the thought
poolside/laguna-xs-2.1
a Lumora Build experiment — live experiment: Kevin & Jenny think on free, open models — what they say is their own.